Most easily identified by the prominent number plate, the Mach
III™ is considered the Cadillac® of disc catching equipment
for the sport of Disc Golf.
Constructed with 24 chains, the Mach III™ is by far the top
disc catching device available in the industry and is the most
widely used catching device found on PDGA approved courses.
If you are planning a course for professional tournament play,
or if you just want the best, the Mach III™ is the top choice of
touring professionals.
Hot-dipped galvanized from the head to toe and guaranteed for
20 years against failure caused by rust and corrosion.
POLE (69 in.) - 1 1/2 in. I.D., 1 15/16 in. O.D. hot dipped
galvanized pipe, drilled.
POLES - The holes closest to one end of the pole are for
the Chain Assembly. This end should also have a red Pole Cap Plug.
The middle set of holes are for the Basket Assembly. The bottom
set of holes are for the Locking Collar for Deluxe Disc Pole Hole¨.
When installing a DPH without an anchor, the middle hole of the
top three holes should face towards the tee.
CHAIN ASSEMBLY- Welded and hot dipped galvanized.
Number Plate - 10 gauge steel, 8 in. diameter. Decal - vinyl numbers
and identification cover. Sleeve (6 in.) - 115/16 in. OD pipe,
drilled. Bolt, hex head nut and nylon insert locknut, hex head
tec screw, internal tooth star lock washer, (will not vibrate
loose like one-way screws). Rod Assembly - 3/8 in. steel rod.
Chain - 12 outer/12 inner chains, 500 lb. test, all hooked to
Chain Assembly with heavy duty "S" Hooks to allow freer
movement of Chains.
CHAIN ASSEMBLY INSTRUCTIONS- Slide Chain Assembly, (rings
first), down Pole. Align holes in Collar with holes in top of
Pole. Fasten with bolt, hex head nut and nylon insert locknut,
hex head tec screw, internal tooth star lock washer, (will not
vibrate loose like one-way screws).
TRAPPER™ BASKET ASSEMBLY - 3/8 in. steel rod, welded
and hot-dipped galvanized. 6 in. Sleeve - bolt, hex head nut and
nylon insert locknut, hex head tec screw, internal tooth star
lock washer, (will not vibrate loose like one-way screws).
TRAPPER™ BASKET ASSEMBLY INSTRUCTIONS - Slide Basket
Assembly down Pole, (basket facing up), until holes in collar
align with holes in middle of Pole. Fasten with bolt, hex head
nut and nylon insert locknut, hex head tec screw, internal tooth
star lock washer, (will not vibrate loose like one-way screws).
DELUXE DISC POLE HOLE ®
only
LOCKING COLLAR - Welded and hot-dipped galvanized.
4 in. Collar - 2 1/8 in. Tubing. Locking Tab - 3/16 in. steel,
punched. Bolt, hex head nut and nylon insert locknut, hex head
tec screw, internal tooth star lock washer, (will not vibrate
loose like one-way screws).
LOCKING COLLAR ASSEMBLY INSTRUCTIONS - Slide the Locking
Collar, with the locking tab at the bottom of Collar, up Pole
to bottom set of holes. Align holes in Locking Collar with holes
in Pole and fasten with bolt, hex head nut and nylon insert locknut,
hex head tec screw, internal tooth star lock washer, (will not
vibrate loose like one-way screws). After the Locking Collar is
fastened, the Pole can be placed in Anchor to complete installation.
*Note: The LOCKING
TAB should always be pointing at the tee.
ANCHOR -18 in. x 2 1/8 in. OD Tubing, drilled. Install
flush to ground with matching Locking Tab aiming at the tee.
CONCRETE & RIVER ROCK (Used to stabilize Anchor until
cement sets) - Approximately 1 cubic foot (concrete, river rock
and lock not furnished).
CAUTION: Let concrete
settle 1 week before installing hardware.
Top of the page